Differences

This shows you the differences between two versions of the page.

--- esp:esp32:flash-commands [2026/09/08 19:14] – [Flash Config Partition] oscar
+++ esp:esp32:flash-commands [2026/09/12 10:25] (current) – oscar
@@ Line 1: / Line 1: @@
-====== Flash Commands ======
+# Flash Commands
 ----
-===== Core tools =====
+## Core tools
 Esp-idf commands can be executed using:
-  * **python**, Located in: ///esp32/idf-tools/python_env/idf5.2_py3.11_env/bin/python//
+  * **idf.py**, Located in: ./esp32/esp-idf/tools/idf.py/
-  * **idf.py**, Located in: ///esp32/esp-idf/tools/idf.py//
+  * **python**, Located in: ./esp32/idf-tools/python_env/idf6.1_py3.13_env/bin/python
-  * **esptool.py**, Located in: ///esp32/idf-tools/python_env/idf5.2_py3.11_env/bin/esptool.py//
+  * **esptool**, Located in: ./esp32/idf-tools/python_env/idf6.1_py3.13_env/bin/esptool
 **idf.py** to be invoked as:
-<code>
+```
 $ idf.py <parameters>
-</code>
+```
+**esptool** can be invoked in different ways:
-**esptool.py** can be invoked in different ways:
+```
-<code>
 $ esptool <parameters>
 $ python -m esptool <parameters>
-</code>
+```
+## Full Flash
-===== Full Flash =====
+```
-<code>
 idf.py -p /dev/ttyACM0 flash
-python -m esptool --chip esp32c3 -p /dev/ttyACM0 -b 460800 --before default_reset --after hard_reset write_flash --flash_mode dio --flash_size 4MB --flash_freq 80m 0x0 build/bootloader/bootloader.bin 0x8000 build/partition_table/partition-table.bin 0xd000 build/ota_data_initial.bin 0x10000 build/LCR-Meter.bin 0x250000 default.config
+python -m esptool --chip esp32c3 -p /dev/ttyACM0 -b 460800 --before default-reset --after hard-reset write-flash --flash_mode dio --flash_size 4MB --flash-freq 80m 0x0 build/bootloader/bootloader.bin 0x8000 build/partition_table/partition-table.bin 0xd000 build/ota_data-initial.bin 0x10000 build/LCR-Meter.bin 0x250000 default.config
-</code>
+```
 Where parameters are:
   * write_flash
@@ Line 31: / Line 28: @@
   * --before default_reset
   * --after hard_reset
-  * --flash_mode dio
+  * --flash-mode dio
-  * --flash_size **detect** or 4MB
+  * --flash-size **detect** or 4MB
-  * --flash_freq **80m** or 40m
+  * --flash-freq **80m** or 40m
   * partition 1 = 0x0 build/bootloader/bootloader.bin
   * partition 2 = 0x8000 build/partition_table/partition-table.bin
   * partition 3 = 0xd000 build/ota_data_initial.bin
   * partition 4 = 0x10000 build/LCR-Meter.bin
-===== Flash Application Partition =====
+## Flash Application Partition
 Use following examples to write to flash:
-<code>
+```
 esptool -chip esp32c3 -p /dev/ttyACM0 -b 460800 --before default-reset --after hard-reset write-flash --flash-mode dio --flash-size detect --flash-freq 80m 0x10000 build/ESR-Meter.bin
@@ Line 46: / Line 43: @@
 python ../../esp-idf/components/esptool_py/esptool/esptool.py -p /dev/ttyUSB0 -b 460800 --before default-reset --after hard-reset --chip esp32  write-flash --flash_mode dio --flash-size detect --flash-freq 40m 0x00130000 build/thermometer.bin
-</code>
+```
 Where parameters are:
@@ Line 59: / Line 56: @@
   * --flash-freq **80m** or 40m
   * 0x10000 build/ESR-Meter.bin
-===== Flash Config Partition =====
+## Flash Config Partition =====
-=== Write Config to partition ===
+### Write Config to partition ===
   esptool --port /dev/ttyACM0  write-flash --flash-mode qio  0x250000 default.config
-=== Read CONFIG from partition ===
+### Read CONFIG from partition ===
   esptool --port /dev/ttyACM0 -b 460800 --before default-reset --chip esp32c3 read-flash 0x250000 4096 downloaded.config