android:oneplus:links
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
| android:oneplus:links [2020/09/16 15:13] – external edit 127.0.0.1 | android:oneplus:links [2022/02/07 20:01] (current) – oscar | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== | + | ====== |
| - | ===== Basic requirements | + | * [[https:// |
| - | * Ensure that the device is on the latest Android 10 firmware. | + | * [[https://forum.xda-developers.com/ |
| - | * Ensure that the device has at least 60% battery remaining. | + | * [[https://forum.xda-developers.com/oneplus-6t|XDA OnePlus 6T - forum]] |
| - | * First: if you use anything else than a PIN code to unlock your phone, change it now. Last TWRP image for Android 10 asks for a data decryption password. It will be easier if it’s a PIN code. Go to Settings > System > Security and change your screen locking choice by a PIN code. | + | * [[https:// |
| - | * Make sure your computer has adb and fastboot. Setup instructions can be found here. | + | |
| - | ===== Unlock Bootloader ===== | + | * [[https://forum.xda-developers.com/ |
| - | The steps below only need to be run once per device. Unlocking the bootloader will erase all data on your device! | + | |
| - | - Prepare phone: | + | |
| - | - Enable Developer options: Settings > System > About. Tap repeatedly on “build number” | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | - Enable | + | |
| - | | + | |
| - | - Boot into fastboot mode. Open a terminal window, and type: < | + | |
| - | | + | |
| - | | + | |
| - | - If the device doesn’t automatically reboot, reboot it. It should now be unlocked. | + | |
| - | | + | |
| - | | + | |
| - | ===== Install TWRP ===== | + | |
| - | The OnePlus 6T uses the newer AB partition scheme first introduced on the Pixel 1. As such there is no recovery partition. Instead, the recovery is part of the boot image. You will temporarily boot TWRP to perform and later perform a more permanent TWRP installation. | + | |
| - | + | ||
| - | First: if you use anything else than a PIN code to unlock your phone, change it now. Last TWRP image for Android 10 asks for a data decryption password. It will be easier if it’s a PIN code. Go to Settings > System > Security and change your screen locking choice by a PIN code. | + | |
| - | + | ||
| - | | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | - place Magisk & TWRP installer zip on Device Internal Memory | + | |
| - | - place TWRP img on your PC | + | |
| - | - Boot into fastboot bootloader mode. Open a terminal window, and type: < | + | |
| - | | + | |
| - | | + | |
| - | - Now in TWRP, tap on Install and browse to the zip and install TWRP (the zip will probably be in /sdcard/Downloads). | + | |
| - | | + | |
| - | | + | |
| - | + | ||
| - | ===== Gaining Root Access ===== | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | - Navigate to Install and select Magisk to root. | + | |
| - | | + | |
| - | | + | |
| - | Keep in mind that the first boot after wiping the phone may take longer than usual, as the phone will need to rebuild the dalvik cache and initialize other first boot and might reboot a few times. | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | ===== Links ===== | + | |
| - | [[https:// | + | |
| - | + | ||
| - | [[https:// | + | |
android/oneplus/links.1600269230.txt.gz · Last modified: (external edit)
